home *** CD-ROM | disk | FTP | other *** search
Text File | 2009-12-11 | 82.1 KB | 2,015 lines |
- -- *****************************************************************
- -- CISCO-WIRELESS-DOCS-EXT-MIB.my:
- -- Cisco Wireless DOCS extension MIB file
- --
- -- January 2000, Saradha Srinivasan
- --
- -- Copyright (c) 2000 by Cisco Systems, Inc.
- -- All rights reserved.
- -- *****************************************************************
-
- CISCO-WIRELESS-DOCS-EXT-MIB DEFINITIONS ::= BEGIN
-
- IMPORTS
- MODULE-IDENTITY,
- OBJECT-TYPE,
- NOTIFICATION-TYPE,
- Integer32,
- Counter32,
- IpAddress
- FROM SNMPv2-SMI
- TruthValue,
- DisplayString,
- MacAddress,
- TimeStamp,
- RowStatus,
- TimeInterval
- FROM SNMPv2-TC
- OBJECT-GROUP,
- MODULE-COMPLIANCE
- FROM SNMPv2-CONF
- ifIndex
- FROM IF-MIB
- cwdIfHeServiceEntry,
- cwdIfHeSuStatusEntry,
- cwdIfHeSuStatusIndex,
- cwdIfHeMacEntry,
- cwdIfHeSuStatusMacAddress,
- cwdIfHeSuStatusIpAddress,
- cwdIfHeSuStatusDownChanIfIndex,
- cwdIfHeSuStatusUpChanIfIndex,
- cwdIfHeSuStatusServiceId,
- cwdIfQosProfileEntry,
- cwdIfQosProfIndex
- FROM CISCO-WIRELESS-DOCS-IF-MIB
- ciscoMgmt
- FROM CISCO-SMI;
-
- ciscoWirelessDocsExtMIB MODULE-IDENTITY
- LAST-UPDATED "200007171003Z"
- ORGANIZATION "Cisco Systems, Inc."
- CONTACT-INFO
- "Cisco Systems
- Customer Service
-
- Postal: Cisco Systems
- 170 West Tasman Drive
- San Jose, CA 95134
- U.S.A.
- Phone: +1 800 553-NETS
- E-mail: wireless-nms@cisco.com"
- DESCRIPTION
- "This MIB module defines Cisco-specific objects that
- add to the functionality defined in
- CISCO-WIRELESS-DOCS-IF-MIB.
- These objects configure the scheduler that supports
- Quality of Service (QoS) of MCNS/DOCSIS compliant
- Radio Frequency (RF) interfaces in Wireless
- Headends (HE)."
- REVISION "200007171003Z"
- DESCRIPTION
- "Initial version"
- ::= { ciscoMgmt 169 }
-
- ciscoWirelessDocsExtMIBObjects OBJECT IDENTIFIER ::=
- { ciscoWirelessDocsExtMIB 1 }
-
- cwdxQosCtrlObjects OBJECT IDENTIFIER ::= { ciscoWirelessDocsExtMIBObjects 1 }
- cwdxQosQueueObjects OBJECT IDENTIFIER ::= { ciscoWirelessDocsExtMIBObjects 2 }
- cwdxHeSuCpeObjects OBJECT IDENTIFIER ::= { ciscoWirelessDocsExtMIBObjects 3 }
- cwdxQosProfileExtObjects OBJECT IDENTIFIER ::=
- { ciscoWirelessDocsExtMIBObjects 4 }
-
-
- --
- -- Scheduler QoS Control Group
- --
- -- This group contains objects that configure how the scheduler
- -- controls traffic. In addition, it contains objects to monitor
- -- the scheduler's admission and rate control.
- --
- -- For each Service ID, there is one Quality of Service profile
- -- associated with it. The QoS profile limits the request (upstream)/
- -- packet (downstream) size for the Service ID and also defines the
- -- minimum guaranteed upstream bandwidth. Each SU's request
- -- associated with a Service ID needs to follow the Quality of
- -- Service profile constraints.
- --
-
- --
- -- Quality of Service control upstream table
- --
- -- Quality of Service control objects for the upstream interface
- --
- -- This table contains objects to configure upstream admission control
- -- based on available upstream bandwidth. This table also contains
- -- objects that show the status of the scheduler.
-
-
- cwdxQosCtrlUpTable OBJECT-TYPE
- SYNTAX SEQUENCE OF CwdxQosCtrlUpEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "For each upstream interface, this table maintains a number
- of objects related to Quality of Service scheduler.
- These objects are used to control SU registration."
- ::= { cwdxQosCtrlObjects 1 }
-
- cwdxQosCtrlUpEntry OBJECT-TYPE
- SYNTAX CwdxQosCtrlUpEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "A list of attributes for each upstream MAC scheduler
- that supports Quality of Service. Entries in this table
- exist for each ifEntry with ifType of
- propDocsWirelessUpstream(nnn)."
- REFERENCE
- "Data-Over-Cable Service Interface Specifications (DOCSIS)
- Radio Frequency Interface Specification (SP-RFI-I04-980724),
- section 6.4 and appendix C.
-
- cwdIfQosProfileTable and cwdIfHeServiceTable in
- CISCO-WIRELESS-DOCS-IF-MIB.my."
- INDEX { ifIndex }
- ::= { cwdxQosCtrlUpTable 1 }
-
- CwdxQosCtrlUpEntry ::= SEQUENCE {
- cwdxQosCtrlUpAdmissionCtrl TruthValue,
- cwdxQosCtrlUpMaxRsvdBWPercent Integer32,
- cwdxQosCtrlUpAdmissionRejects Counter32,
- cwdxQosCtrlUpReservedBW Integer32,
- cwdxQosCtrlUpMaxVirtualBW Integer32
- }
-
- cwdxQosCtrlUpAdmissionCtrl OBJECT-TYPE
- SYNTAX TruthValue
- MAX-ACCESS read-write
- STATUS current
- DESCRIPTION
- "The admission control status for this upstream entry.
-
- When this object is set to 'true', the upstream scheduler
- will check the virtual reserved bandwidth remaining
- before giving admission to this new SU. If there
- is not enough reserved bandwidth to serve the SU's minimum
- guaranteed bandwidth, the registration request will be
- rejected.
-
- This object is set to 'false' to disable admission control.
- That is, there will be no checking for bandwidth capacity and
- the upstream interface scheduler just admits SU registration
- requests."
- ::= { cwdxQosCtrlUpEntry 1 }
-
- cwdxQosCtrlUpMaxRsvdBWPercent OBJECT-TYPE
- SYNTAX Integer32 (10..1000)
- UNITS "percent"
- MAX-ACCESS read-write
- STATUS current
- DESCRIPTION
- "The percentage of upstream maximum reserved bandwidth to the
- raw bandwidth if the admission control is enabled on this
- upstream.
-
- For example, if the upstream interface has raw bandwidth
- 1,600,000 bits/second and cwdxQosCtrlUpMaxRsvdBWPercent is 200
- percent, then this upstream scheduler will set the maximum of
- virtual reserved bandwidth capacity to 3,200,000 bits/second
- (1,600,000 * 2) to serve Subscriber-units with minimum guaranteed
- upstream bandwidth.
-
- The default value is 100 percent (that is, maximum reserved
- bandwidth is the raw bandwidth.) Whenever the admission control
- is changed (on to off, off to on), this value will be reset to
- the default value 100.
-
- If the admission control is disabled, the value will be reset
- to 100 (the default value)."
- REFERENCE
- "Data-Over-Cable Service Interface Specifications (DOCSIS)
- Radio Frequency Interface Specification
- (SP-RFI-I04-980724). section 6.4 and appendix C."
- ::= { cwdxQosCtrlUpEntry 2 }
-
- cwdxQosCtrlUpAdmissionRejects OBJECT-TYPE
- SYNTAX Counter32
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The count of SU registration requests rejected on this
- upstream interface. The rejection is due to insufficient
- available bandwidth for this SU. The requests are rejected
- only when cwdxQosCtrlUpAdmissionCtrl is 'true' on this
- upstream interface."
- ::= { cwdxQosCtrlUpEntry 3 }
-
- cwdxQosCtrlUpReservedBW OBJECT-TYPE
- SYNTAX Integer32 (0..102400000)
- UNITS "bits/second"
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The current total reserved bandwidth in bits per second of this
- upstream interface. It is the sum of all SUs' minimum
- guaranteed bandwidth in bits per second currently supported
- on this upstream."
- ::= { cwdxQosCtrlUpEntry 4 }
-
- cwdxQosCtrlUpMaxVirtualBW OBJECT-TYPE
- SYNTAX Integer32 (0..102400000)
- UNITS "bits/second"
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The maximum virtual bandwidth capacity of this upstream interface
- if the admission control is enabled. It is the raw bandwidth
- in bits per second times the percentage. If the admission
- control is disabled, then this object will contain the value
- zero."
- ::= { cwdxQosCtrlUpEntry 5 }
-
- --
- -- Rate Limiting table
- --
- -- After a SU is registered, upstream and downstream schedulers
- -- will control the bandwidth request/packet size to ensure the Quality of
- -- Service and fairness by a rate limiting algorithm. This table
- -- contains attributes related to the rate limiting algorithms.
- --
-
- cwdxQosIfRateLimitTable OBJECT-TYPE
- SYNTAX SEQUENCE OF CwdxQosIfRateLimitEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "This table describes the attributes of rate limiting for
- schedulers in upstream and downstream interfaces that
- support Quality of Service. The rate limiting process is
- to ensure the Quality of Service and fairness."
- ::= { cwdxQosCtrlObjects 2 }
-
- cwdxQosIfRateLimitEntry OBJECT-TYPE
- SYNTAX CwdxQosIfRateLimitEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "List of the rate limiting attributes for upstream and
- downstream interfaces schedulers that support Quality of
- Service. Entries in this table exist for each ifEntry with
- ifType of propDocsWirelessUpstream(nnn) and
- propDocsWirelessDownstream(nnn)."
- REFERENCE
- "Data-Over-Cable Service Interface Specifications (DOCSIS)
- Radio Frequency Interface Specification (SP-RFI-I04-980724),
- section 6.4 and appendix C.
-
- cwdIfQosProfileTable and cwdIfHeServiceTable in
- CISCO-DOCS-WIRELESS-IF-MIB.my."
- INDEX { ifIndex }
- ::= { cwdxQosIfRateLimitTable 1 }
-
- CwdxQosIfRateLimitEntry ::= SEQUENCE {
- cwdxQosIfRateLimitAlgo INTEGER,
- cwdxQosIfRateLimitExpWgt Integer32,
- cwdxQosIfRateLimitShpMaxDelay INTEGER,
- cwdxQosIfRateLimitShpGranularity INTEGER
- }
-
- cwdxQosIfRateLimitAlgo OBJECT-TYPE
- SYNTAX INTEGER {
- noRateLimit(1), -- rate limiting process is disabled
- oneSecBurst(2), -- Bursty 1 second token bucket algorithm
- carLike(3), -- Average token usage algorithm (CAR-like)
- wgtExPacketDiscard(4), -- Weighted excess packet discard
- -- algorithm
- shaping(5) -- token bucket algorithm with shaping
- }
- MAX-ACCESS read-write
- STATUS current
- DESCRIPTION
- "To ensure fairness, at the upstream, the HE will throttle
- the rate of bandwidth grants, such that the flow never
- gets more than its provisioned peak rate in bps.
- Similarly at the downstream, HE controls the packets
- sent such that flow never gets more than its provisioned
- peak rate in bps.
-
- There are two directions for every Service Id (Sid) traffic:
- downstream and upstream. Each direction is called a service
- flow here and is assigned one token bucket with chosen
- algorithm.
-
- The enumerations for the rate limiting algorithm are:
- noRateLimit(1): The rate limiting is disabled. No rate
- limiting.
- oneSecBurst(2): Bursty 1 second token bucket algorithm.
- carLike(3) : Average token usage (CAR-like) algorithm
- wgtExPacketDiscard(4) : Weighted excess packet discard
- algorithm.
- shaping(5): token bucket algorithm with shaping
-
- Upstream supports all the above except
- wgtExtPacketDiscard(4).
-
- Downstream supports all the above rate-limiting algorithms.
-
- Token bucket algorithm with shaping is the
- default algorithm for upstream.
-
- Bursty 1 second token bucket algorithm is the
- default algorithm for downstream.
-
- Each algorithm is described as below:
- No rate limiting:
- The rate limiting process is disabled and no checking
- against the maximum bandwidth allowed.
-
- Bursty 1 second token bucket rate limiting algorithm:
- In this algorithm, at the start of every 1 second interval,
- a service flow's token usage is reset to 0, and every time
- the modem for that service flow sends a request (upstream) /
- packet (downstream) the upstream/downstream bandwidth
- token usage is incremented by the size of the
- request/packet sent. As long as the service flow's bandwidth
- token usage is less than the maximum bandwidth in bits
- per second (peak rate limit) its QoS service class
- allows, the request/packets will not be restricted.
- Once the service flow has sent more than its peak rate in the
- one second interval, it is prevented from sending more
- data by rejecting request (upstream) or dropping
- packets (downstream). This is expected to slow down
- the higher layer sources. The token usage counter gets
- reset to 0 after the 1 second interval has elapsed. The
- modem for that service flow is free to send more data up to the
- peak rate limit in the new 1 second interval that follows.
-
- Average token usage (Cisco CAR like) algorithm:
- This algorithm maintains a continuous average of the
- burst token usage of a service flow. There is no sudden
- refilling of tokens every 1 second interval. Every time a
- request/packet is to be handled, the scheduler tries to see
- how much time has elapsed since last transmission, and
- computes the number of tokens accumulated by this service flow
- at its QoS class peak rate. If burst usage of the service flow
- is less than tokens accumulated, the burst usage is reset to 0
- and request/packet is forwarded. If the service flow has
- accumulated fewer tokens than its burst usage, the burst usage
- shows an outstanding balance usage after decrementing by the
- tokens accumulated. In such cases, the request/packet is still
- forwarded, provided the service flow's outstanding usage does
- not exceed peak rate limit of its QoS class. If outstanding
- burst usage exceeds the peak rate of the class, the service
- flow is given some token credit up to a certain maximum credit
- limit and the request/packet is forwarded. The request/packet
- is dropped when outstanding usage exceeds peak rate and maximum
- credit has been used up by this service flow. This algorithm
- tracks long term average bandwidth usage of the service flow
- and controls this average usage at the peak rate limit.
-
- Weighted excess packet discard algorithm:
- This rate limiting algorithm is only available as an option
- for downstream rate limiting. The algorithm is to maintain an
- weighted exponential moving average of the loss rate of a
- service flow over time. The loss rate, expressed in packets,
- represents the number of packets that can be sent from this
- service flow in a one second interval before a packet will
- be dropped. At every one second interval, the loss rate gets
- updated using the ratio between the flow peak rate (in bps)
- in its QoS profile and the service flow actual usage (in bps).
- If the service flow begins to send more than its peak rate
- continuously, the number of packets it can send in an one
- second interval before experiencing a drop will slowly keep
- reducing until SU for that service flow slows down
- as indicated by actual usage less or equal to the peak rate.
-
- Token bucket algorithm with shaping:
- If there is no QoS class peak rate limit, forward the
- request/packet without delay. If there is a QoS peak rate
- limit, every time a request/packet is to be handled, the
- scheduler determines the number of bandwidth tokens that this
- service flow has accumulated over the elapsed time at its
- QoS class peak rate and increments the tokens counter of the
- service flow accordingly. The scheduler limits the token
- count to the maximum transmit burst (token bucket depth).
- If token count is greater than the number of tokens required
- to handle current request/packet, decrement token count by
- size of request/packet and forwards the request/packet
- without delay. If token count is less than the size of
- request/packet, compute the shaping delay time after
- which the deficit number of tokens would be available. If
- shaping delay time is less than the maximum shaping delay,
- decrement tokens count by size of request/packet and
- forward this request/packet with the shaping delay in the
- shaping delay queue. When the delay time expires, the
- request/packet is forwarded. If shaping delay time is
- greater than the maximum shaping delay that the subsequent
- shaper can handle, the request/packet is dropped. Users can
- use cwdxQosIfRateLimitShpMaxDelay to configure the maximum
- shaping delay and cwdxQosIfRateLimitShpGranularity to
- configure the shaping granularity."
- ::= { cwdxQosIfRateLimitEntry 1 }
-
- cwdxQosIfRateLimitExpWgt OBJECT-TYPE
- SYNTAX Integer32 (1..4)
- MAX-ACCESS read-write
- STATUS current
- DESCRIPTION
- "Weight for exponential moving average of loss rate,
- when using weighted excess packet discard algorithm.
- The higher values of the weight make the algorithm
- more sensitive to the recent bandwidth usage by the Sid.
-
- The default value is 1. Whenever the rate limiting
- algorithm is changed to weighted excess packet discard
- algorithm, this value will be reset to the default 1.
-
- If the rate limiting algorithm is not weighted excess
- packet discard algorithm, the value will be always the
- default value 1. You will not be able to set it to
- anything other than 1 when it is not weighted excess
- packet discard algorithm."
- ::= { cwdxQosIfRateLimitEntry 2 }
-
- cwdxQosIfRateLimitShpMaxDelay OBJECT-TYPE
- SYNTAX INTEGER {
- na(1),
- msec128(2),
- msec256(3),
- msec512(4),
- msec1024(5)
- }
- MAX-ACCESS read-write
- STATUS current
- DESCRIPTION
- "The maximum shaping delay in milliseconds. That is, the maximum
- amount of time for which the HE will allow buffering of any
- rate exceeded flow. If the max buffering delay is large,
- then grants/packets of the flow will be buffered for a
- longer period of time even though the flow is rate exceeded.
- This means fewer chances of drops for such rate exceeded
- flow. However, too large a max shaping delay can result in
- quick drainage of packet buffers at the HE, since several
- packets will be in the shaping (delay) queue waiting for
- their proper transmission time. Another important point to
- note is that delaying a flow's packets (especially TCP
- flows) for extended periods of time may be counter-
- productive, since the higher protocol layers may assume
- a packet loss after a certain amount of time.
-
- The maximum shaping delay is only applied to rate limit
- algorithm: Token bucket algorithm with shaping. If the rate
- limit algorithm is not Token bucket algorithm with shaping,
- the value is always na(1) which is not applicable. In this
- case, you will be allowed to set the value to na(1) only.
-
- If the token count is less than the size of request/packet, HE
- computes the shaping delay time after which the deficit number of
- tokens would be available. If the shaping delay time is greater
- than the maximum shaping delay, the request/packet will be
- dropped.
-
- The enumerations for cwdxQosIfRateLimitShpMaxDelay are:
- na(1): maximum shaping delay is not applied to the current
- rate limit algorithm
- msec128(2): maximum shaping delay is 128 milliseconds
- msec256(3): maximum shaping delay is 256 milliseconds
- msec512(4): maximum shaping delay is 512 milliseconds
- msec1024(5): maximum shaping delay is 1024 milliseconds
-
- At the downstream, cwdxQosIfRateLimitShpMaxDelay
- is configurable and the default value is msec128(2).
- Whenever the downstream rate limit algorithm is changed
- to Token bucket algorithm with shaping from other rate
- limit algorithm, the value will be reset to the default
- value.
-
- At the upstream, cwdxQosIfRateLimitShpMaxDelay is not
- configurable and it is read-only value."
- ::= { cwdxQosIfRateLimitEntry 3 }
-
- cwdxQosIfRateLimitShpGranularity OBJECT-TYPE
- SYNTAX INTEGER {
- na(1),
- msec1(2),
- msec2(3),
- msec4(4),
- msec8(5),
- msec16(6)
- }
- MAX-ACCESS read-write
- STATUS current
- DESCRIPTION
- "The width in milliseconds of each element in shaping
- delay queue, that is, the shaping granularity.
-
- The shaping granularity is only applied to rate limit
- algorithm: Token bucket algorithm with shaping. It
- controls how accurately the algorithm quantizes the shaping
- delay for a rate exceeded flow. If granularity is large, several
- shaping delay values will all be quantized to the same element
- in the queue resulting in less accurate rate shaping for the flows
- in bits/sec. On the other hand, choosing too small granularity
- causes more memory to be used for the shaper block, and also
- can cost a bit more in runtime overhead.
-
- If the rate limit algorithm is not Token bucket algorithm with
- shaping, the value is always na(1) which is not applicable.
- Setting to any thing other than na(1) will be rejected.
-
- The enumerations for shaping granularity are:
- na(1): shaping granularity is not applied to the current
- rate limit algorithm
- msec1(2): shaping granularity in 1 milliseconds
- msec2(3): shaping granularity in 2 milliseconds
- msec4(4): shaping granularity in 4 milliseconds
- msec8(5): shaping granularity in 8 milliseconds
- msec16(6): shaping granularity in 16 milliseconds
-
- At the downstream, this object is configurable and the
- default value is msec4(4). Whenever the downstream rate limit
- algorithm is changed to Token bucket algorithm with shaping
- from other rate limit algorithm, the value will be reset to the
- default value. When the algorithm is Token bucket algorithm
- with shaping and set to same algorithm again the value will
- not be reset to default value.
-
- At the upstream, this object is not configurable and
- it is read-only value."
- ::= { cwdxQosIfRateLimitEntry 4 }
-
- --
- -- He Service Extension Table
- --
- -- This table extends the information about a Service ID in
- -- cwdIfHeServiceTable.
- --
- -- For each Service ID, there is one Quality of Service profile
- -- associated with it and the profile limitsthe request/packet size
- -- ratio for the Service ID. This table shows downstream traffic
- -- statistics. It also counts requests and packets that exceeded
- -- the limits set in the QOS profile for each SID.
- --
-
- cwdxHeServiceExtTable OBJECT-TYPE
- SYNTAX SEQUENCE OF CwdxHeServiceExtEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "The list contains the additional attributes of a single Service
- ID that provided by cwdIfHeServiceEntry."
- ::= { cwdxQosCtrlObjects 3 }
-
- cwdxHeServiceExtEntry OBJECT-TYPE
- SYNTAX CwdxHeServiceExtEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "Additional objects for cwdIfHeServiceTable entry including
- downstream traffic statistics and excess counts against the
- Quality of Service limits for each Service ID."
- REFERENCE
- "Data-Over-Cable Service Interface Specifications (DOCSIS)
- Radio Frequency Interface Specification (SP-RFI-I04-980724),
- section 6.4 and appendix C.
-
- cwdIfQosProfileTable and cwdIfHeServiceTable in
- CISCO-WIRELESS-DOCS-IF-MIB.my."
- AUGMENTS { cwdIfHeServiceEntry }
- ::= { cwdxHeServiceExtTable 1 }
-
- CwdxHeServiceExtEntry ::= SEQUENCE {
- cwdxIfHeServiceOutOctets Counter32,
- cwdxIfHeServiceOutPackets Counter32,
- cwdxQosMaxUpBWExcessRequests Counter32,
- cwdxQosMaxDownBWExcessPackets Counter32
- }
-
- cwdxIfHeServiceOutOctets OBJECT-TYPE
- SYNTAX Counter32
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The cumulative number of Packet Data octets sent for this
- Service ID."
- ::= { cwdxHeServiceExtEntry 1 }
-
- cwdxIfHeServiceOutPackets OBJECT-TYPE
- SYNTAX Counter32
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The cumulative number of Packet data packets sent for this
- Service ID."
- ::= { cwdxHeServiceExtEntry 2 }
-
-
- cwdxQosMaxUpBWExcessRequests OBJECT-TYPE
- SYNTAX Counter32
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The number of upstream bandwidth requests which exceeds the
- maximum upstream bandwidth allowed for a service defined
- in the Quality of Service profile associated with this Sid.
- The request which exceeds the maximum upstream bandwidth
- allowed will be rejected by the upstream's rate limiting
- process using one of the rate limiting algorithm.
-
- Note that the value of this counter cannot be directly used
- to know the number of upstream packets that got dropped at
- the SU. A single upstream packet drop of a SU
- can result in up to 16 increments in this counter, since the
- SU keeps retrying and keeps getting bandwidth request
- drops at HE if it has consumed its peak rate."
- REFERENCE
- "cwdIfQosProfMaxUpBandwidth object in
- CISCO-WIRELESS-DOCS-IF-MIB.my."
- ::= { cwdxHeServiceExtEntry 3 }
-
- cwdxQosMaxDownBWExcessPackets OBJECT-TYPE
- SYNTAX Counter32
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The number of downstream bandwidth packets which exceeds the
- maximum downstream bandwidth allowed for a service defined
- in the Quality of Service profile associated with this Sid.
- The packet which exceeds the maximum downstream bandwidth
- allowed will be dropped by the downstream's rate limiting
- process using one of the rate limiting algorithm."
- REFERENCE
- "cwdIfQosProfMaxDownBandwidth object in
- CISCO-WIRELESS-DOCS-IF-MIB.my."
- ::= { cwdxHeServiceExtEntry 4 }
-
-
- --
- -- Scheduler QoS Queue Group
- --
- -- To ensure Quality of Service and fairness, the scheduler
- -- maintains a set of queues for different services and puts
- -- SU requests/packets for that Sid in a different
- -- queue according to the Quality of Service profile of the
- -- Sid. Each queue has a name and order within the queue set.
- -- The scheduler will serve the requests/packets in higher
- -- order queue before serving the requests/packets in lower
- -- order queue.
- --
-
- --
- -- Scheduler bandwidth request queues table
- --
- -- This table displays the attributes for these queues in a
- -- interface scheduler that supports Quality of Service.
- --
-
- cwdxBWQueueTable OBJECT-TYPE
- SYNTAX SEQUENCE OF CwdxBWQueueEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "This table describes the attributes of queues
- in wireless interfaces schedulers that support
- Quality of Service."
- ::= { cwdxQosQueueObjects 1 }
-
- cwdxBWQueueEntry OBJECT-TYPE
- SYNTAX CwdxBWQueueEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "The list of queue attributes in upstream and downstream
- interfaces schedulers that supports Quality of Service.
- Entries in this table exist for each ifEntry with ifType of
- propDocsWirelessUpstream(nnn) and
- propDocsWirelessDownstream(nnn)."
- REFERENCE
- "Data-Over-Cable Service Interface Specifications (DOCSIS)
- Radio Frequency Interface Specification (SP-RFI-I04-980724),
- section 6.4 and appendix C."
- INDEX { ifIndex,cwdxBWQueueNameCode }
- ::= { cwdxBWQueueTable 1 }
-
- CwdxBWQueueEntry ::= SEQUENCE {
- cwdxBWQueueNameCode INTEGER,
- cwdxBWQueueOrder Integer32,
- cwdxBWQueueNumServedBeforeYield Integer32,
- cwdxBWQueueType INTEGER,
- cwdxBWQueueMaxDepth Integer32,
- cwdxBWQueueDepth Integer32,
- cwdxBWQueueDiscards Counter32
- }
-
- cwdxBWQueueNameCode OBJECT-TYPE
- SYNTAX INTEGER {
- cirQ(1), -- Committed Information Rate queue
- tbeQ(2) -- TIERED BEST EFFORT queue
- }
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "The name code for the queue.
- cirQ: CIR queue. The queue is for Committed Information Rate
- (CIR) type of service which serves Service IDs which have
- minimum guaranteed rate in its QoS profile.
- tbeQ: TBE queue. The queue is for TIERED BEST EFFORT type
- service which serves Service IDs which does not have
- minimum guaranteed rate in its QoS profile."
- REFERENCE
- "Data-Over-Cable Service Interface Specifications (DOCSIS)
- Radio Frequency Interface Specification (SP-RFI-I04-980724),
- section 6.4 and appendix C."
- ::= { cwdxBWQueueEntry 1 }
-
- cwdxBWQueueOrder OBJECT-TYPE
- SYNTAX Integer32 (0..10)
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The relative order of this queue to the other queues within the
- wireless interface. The smaller number has higher order. That is,
- 0 is the highest order and 10 is the lowest order. The
- scheduler will serve the requests in higher order queue up to
- the number of requests defined in cwdxBWQueueNumServedBeforeYield
- before serving requests in the next higher order queue.
- The queues with higher priority will not be serviced
- (once the QueueNumServedBeforeYield number has been hit)
- until all remaining queues are processed.
-
- If there are n queues on this interface, the queue order will
- be 0 to n-1 and maximum number of requests defined as
- cwdxBWQueueNumServedBeforeYield in order 0 queue will be served
- before the requests in order 1 queue to be served."
- ::= { cwdxBWQueueEntry 2 }
-
- cwdxBWQueueNumServedBeforeYield OBJECT-TYPE
- SYNTAX Integer32 (0..50)
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The maximum number of requests/packets the scheduler can serve
- before yielding to another queue. The value 0 means all requests
- must be served before yielding to another queue."
- ::= { cwdxBWQueueEntry 3 }
-
-
- cwdxBWQueueType OBJECT-TYPE
- SYNTAX INTEGER {
- unknown(1),
- other(2),
- fifo(3),
- priority(4)
- }
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The queuing type which decides the position of a request/packet
- within the queue.
- unknown : queue type unknown.
- other : not fifo, and not priority.
- fifo : first in first out.
- priority: each bandwidth request has a priority and the
- position of the request within the queue depends
- on its priority."
- ::= { cwdxBWQueueEntry 4 }
-
-
- cwdxBWQueueMaxDepth OBJECT-TYPE
- SYNTAX Integer32
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The maximum number of requests/packets which the queue can
- support."
- ::= { cwdxBWQueueEntry 5 }
-
-
- cwdxBWQueueDepth OBJECT-TYPE
- SYNTAX Integer32
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The current number of requests/packets in the queue."
- ::= { cwdxBWQueueEntry 6 }
-
-
- cwdxBWQueueDiscards OBJECT-TYPE
- SYNTAX Counter32
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The number of requests/packets discarded because of queue
- overflow (queue depth > queue maximum depth)."
- ::= { cwdxBWQueueEntry 7 }
-
-
- --
- -- HE Customer Premises Equipments (CPE) Group
- --
- -- This group contains tables in HE for information about
- -- Customer Premises Equipment (CPE) that connect to SUs.
- --
-
- --
- -- Customer Premises Equipments (CPE) Table
- --
- -- For the information of CPE maintained in HE.
- --
-
- cwdxCpeTable OBJECT-TYPE
- SYNTAX SEQUENCE OF CwdxCpeEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "This table contains information about
- Customer Premises Equipments (CPE)."
- ::= { cwdxHeSuCpeObjects 1 }
-
- cwdxCpeEntry OBJECT-TYPE
- SYNTAX CwdxCpeEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "The list contains information for a Customer Premises
- Equipment (CPE) connected to SUs. An entry exists for
- each Customer Premises Equipment connected to a
- subscriber-unit supported by HE."
- REFERENCE
- "Data-Over-Cable Service Interface Specifications (DOCSIS)
- Radio Frequency Interface Specification (SP-RFI-I04-980724.)
- cwdIfHeSuStatusTable, cwdIfHeServiceTable in
- CISCO-DOCS-WIRELESS-IF-MIB.my."
- INDEX { cwdxCpeStatusIndex, cwdxCpeMacAddress }
- ::= { cwdxCpeTable 1 }
-
- CwdxCpeEntry ::= SEQUENCE {
- cwdxCpeStatusIndex INTEGER,
- cwdxCpeMacAddress MacAddress,
- cwdxCpeIpAddress IpAddress,
- cwdxCpeAccessGroup DisplayString
- }
-
- cwdxCpeStatusIndex OBJECT-TYPE
- SYNTAX INTEGER(1..2147483647)
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "Index to an entry in cwdIfHeSuStatusTable identifying
- status of the SU (which the CPE connects to.)"
- ::= { cwdxCpeEntry 1 }
-
- cwdxCpeMacAddress OBJECT-TYPE
- SYNTAX MacAddress
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "The Mac address to identify a Customer Premises Equipment."
- ::= { cwdxCpeEntry 2 }
-
- cwdxCpeIpAddress OBJECT-TYPE
- SYNTAX IpAddress
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "Ip address of the Customer Premises Equipment."
- ::= { cwdxCpeEntry 3 }
-
-
- cwdxCpeAccessGroup OBJECT-TYPE
- SYNTAX DisplayString
- MAX-ACCESS read-write
- STATUS current
- DESCRIPTION
- "ASCII text to identify the Access Group for a CPE.
- Access Group is to filter the upstream traffic for that
- CPE."
- ::= { cwdxCpeEntry 4 }
-
- --
- cwdxSuMappingTable OBJECT-TYPE
- SYNTAX SEQUENCE OF CwdxSuMappingEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "This table contains a mapping between the SU Mac Address
- and the cwdIfHeSuStatusIndex which identifies a row
- in cwdIfHeSuStatusTable which lists the attributes of
- an SU."
- ::= { cwdxHeSuCpeObjects 2 }
-
- cwdxSuMappingEntry OBJECT-TYPE
- SYNTAX CwdxSuMappingEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "There exists an entry in this table for every SU
- connected to the HE. Each entry contains a mapping
- from the SU's mac address to the cwdIfHeSuStatusIndex."
- REFERENCE
- "Data-Over-Cable Service Interface Specifications (DOCSIS)
- Radio Frequency Interface Specification (SP-RFI-I04-980724.)
- cwdIfHeSuStatusTable, cwdIfHeServiceTable in
- CISCO-DOCS-WIRELESS-IF-MIB.my."
- INDEX { cwdxSuMappingMacAddress }
- ::= { cwdxSuMappingTable 1 }
-
- CwdxSuMappingEntry ::= SEQUENCE {
- cwdxSuMappingMacAddress MacAddress,
- cwdxSuMappingStatusIndex INTEGER
- }
-
- cwdxSuMappingMacAddress OBJECT-TYPE
- SYNTAX MacAddress
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "The Mac address to identify a Subscriber-unit."
- ::= { cwdxSuMappingEntry 2 }
-
- cwdxSuMappingStatusIndex OBJECT-TYPE
- SYNTAX INTEGER(1..2147483647)
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "Index to an entry in cwdIfHeSuStatusTable identifying
- status of the SU."
- ::= { cwdxSuMappingEntry 1 }
-
-
- -- HE SU status extension table
- --
- -- This table extends the SU status information in cwdIfHeSuStatusTable
- --
-
- cwdxHeSuStatusExtTable OBJECT-TYPE
- SYNTAX SEQUENCE OF CwdxHeSuStatusExtEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "The list contains the additional SU status information."
- ::= { cwdxHeSuCpeObjects 3 }
-
- cwdxHeSuStatusExtEntry OBJECT-TYPE
- SYNTAX CwdxHeSuStatusExtEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "Additional objects for cwdIfHeSuStatusTable entry."
- REFERENCE
- "Data-Over-Cable Service Interface Specifications (DOCSIS)
- Radio Frequency Interface Specification (SP-RFI-I04-980724.)
- cwdIfHeSuStatusTable in DOCS-IF-MIB.my."
- AUGMENTS { cwdIfHeSuStatusEntry }
- ::= { cwdxHeSuStatusExtTable 1 }
-
- CwdxHeSuStatusExtEntry ::= SEQUENCE {
- cwdxHeSuStatusValue INTEGER,
- cwdxIfHeSuStatusOnlineTimes Counter32,
- cwdxIfHeSuStatusPercentOnline Integer32,
- cwdxIfHeSuStatusMinOnlineTime TimeInterval,
- cwdxIfHeSuStatusAvgOnlineTime TimeInterval,
- cwdxIfHeSuStatusMaxOnlineTime TimeInterval,
- cwdxIfHeSuStatusMinOfflineTime TimeInterval,
- cwdxIfHeSuStatusAvgOfflineTime TimeInterval,
- cwdxIfHeSuStatusMaxOfflineTime TimeInterval,
- cwdxIfHeSuStatusDynSidCount INTEGER
- }
-
- cwdxHeSuStatusValue OBJECT-TYPE
- SYNTAX INTEGER {
- offline(1),
- others(2),
- initRangingRcvd(3),
- initDhcpReqRcvd(4),
- onlineNetAccessDisabled(5),
- onlineKekAssigned(6),
- onlineTekAssigned(7),
- rejectBadMic(8),
- rejectBadCos(9),
- kekRejected(10),
- tekRejected(11),
- online(12),
- initTftpPacketRcvd(13),
- initTodRequestRcvd(14)
- }
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "Current Subscriber-unit connectivity state. The object extends
- states in cwdIfHeSuStatusValue in more detail.
-
- The enumerations are:
- offline(1) : SU considered offline.
- others(2) : states is in cwdIfHeSuStatusValue.
- initRangingRcvd(3) : SU sent initial ranging.
- initDhcpReqRcvd(4) : dhcp request received.
- onlineNetAccessDisabled(5): SU registered, but network
- access for the SU is disabled.
- onlineKekAssigned(6) : SU registered, BPI enabled and KEK
- assigned.
- onlineTekAssigned(7) : SU registered, BPI enabled and TEK
- assigned.
- rejectBadMic(8) : SU did attempt to register but
- registration was refused due to bad mic.
- rejectBadCos(9) : SU did attempt to register but
- registration was refused due to bad COS.
- kekRejected(10) : KEK SU key assignment rejected.
- tekRejected(11) : TEK SU key assignment rejected.
- online(12) : SU registered, enabled for data.
- initTftpPacketRcvd(13): tftp packet received and option file
- transfer started.
- initTodRquestRcvd(14): Time of the Day (TOD) request received.
-
- The ranging, rangingAborted, rangingComplete, and ipComplete
- states in cwdIfHeSuStatusValue are all represented
- by the 'others' value in this object.
-
- The registrationComplete state in cwdIfHeSuStatusValue
- could be online, onlineNetAccessDisabled, onlineKekAssigned, or
- onlineTekAssigned in this object.
-
- The accessDenied state in cwdIfHeSuStatusValue could be
- rejectBadMic, rejectBadCos in this object for the possible
- reasons of Subscriber-unit registration abort.
-
- The HE only reports states it is able to detect."
- ::= { cwdxHeSuStatusExtEntry 1 }
-
- cwdxIfHeSuStatusOnlineTimes OBJECT-TYPE
- SYNTAX Counter32
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The number of times that the SU changes the connectivity
- state from 'offline' to 'online' over the time period from
- the SU's first ranging message received by HE until now.
-
- The SU is considered as 'online' when the value for
- cwdxHeSuStatusValue is any of the values: online(5),
- onlineNetAccessDisabled(6), onlineKekAssigned(7), and
- onlineTekAssigned(8), and the SU is considered as 'offline'
- for other values for cwdxHeSuStatusValue."
- REFERENCE
- "cwdxHeSuStatusValue object."
- ::= { cwdxHeSuStatusExtEntry 2 }
-
- cwdxIfHeSuStatusPercentOnline OBJECT-TYPE
- SYNTAX Integer32 (0..10000)
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The percentage of time that the SU stays 'online' over
- the time period from the SU's first ranging message
- received by HE until now.
-
- The value for this object is 100 times bigger than the real
- percentage value. For example, 32.15% will be value 3215.
-
- The SU is considered as 'online' when the value for
- cwdxHeSuStatusValue is any of the values: online(5),
- onlineNetAccessDisabled(6), onlineKekAssigned(7), and
- onlineTekAssigned(8), and the SU is considered as
- 'offline' for other values for cwdxHeSuStatusValue."
- REFERENCE
- "cwdxHeSuStatusValue object."
- ::= { cwdxHeSuStatusExtEntry 3 }
-
- cwdxIfHeSuStatusMinOnlineTime OBJECT-TYPE
- SYNTAX TimeInterval
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The minimum period of time the SU stayed 'online' over
- the time period from the SU's first ranging message
- received by HE until now.
-
- The SU is considered as 'online' when the value for
- cwdxHeSuStatusValue is any of the values: online(5),
- onlineNetAccessDisabled(6), onlineKekAssigned(7), and
- onlineTekAssigned(8), and the SU is considered as
- 'offline' for other values for cwdxHeSuStatusValue."
- REFERENCE
- "cwdxHeSuStatusValue object."
- ::= { cwdxHeSuStatusExtEntry 4 }
-
-
- cwdxIfHeSuStatusAvgOnlineTime OBJECT-TYPE
- SYNTAX TimeInterval
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The average period of time the SU stayed 'online' over
- the time period from the SU's first ranging message
- received by HE until now.
-
- The SU is considered as 'online' when the value for
- cwdxHeSuStatusValue is any of the values: online(5),
- onlineNetAccessDisabled(6), onlineKekAssigned(7), and
- onlineTekAssigned(8), and the SU is considered as
- 'offline' for other values for cwdxHeSuStatusValue."
- REFERENCE
- "cwdxHeSuStatusValue object."
- ::= { cwdxHeSuStatusExtEntry 5 }
-
- cwdxIfHeSuStatusMaxOnlineTime OBJECT-TYPE
- SYNTAX TimeInterval
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The maximum period of time the SU stayed 'online' over
- the time period from the SU's first ranging message
- received by HE until now.
-
- The SU is considered as 'online' when the value for
- cwdxHeSuStatusValue is any of the values: online(5),
- onlineNetAccessDisabled(6), onlineKekAssigned(7), and
- onlineTekAssigned(8), and the SU is considered as
- 'offline' for other values for cwdxHeSuStatusValue."
- REFERENCE
- "cwdxHeSuStatusValue object."
- ::= { cwdxHeSuStatusExtEntry 6 }
-
- cwdxIfHeSuStatusMinOfflineTime OBJECT-TYPE
- SYNTAX TimeInterval
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The minimum period of time SU stayed 'offline' over
- the time period from the SU's first ranging message
- received by HE until now.
-
- The SU is considered as 'online' when the value for
- cwdxHeSuStatusValue is any of the values: online(5),
- onlineNetAccessDisabled(6), onlineKekAssigned(7), and
- onlineTekAssigned(8), and the SU is considered as
- 'offline' for other values for cwdxHeSuStatusValue."
- REFERENCE
- "cwdxHeSuStatusValue object."
- ::= { cwdxHeSuStatusExtEntry 7 }
-
-
- cwdxIfHeSuStatusAvgOfflineTime OBJECT-TYPE
- SYNTAX TimeInterval
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The average period of time the SU stayed 'offline' over
- the time period from the SU's first ranging message
- received by HE until now.
-
- The SU is considered as 'online' when the value for
- cwdxHeSuStatusValue is any of the values: online(5),
- onlineNetAccessDisabled(6), onlineKekAssigned(7), and
- onlineTekAssigned(8), and the SU is considered as
- 'offline' for other values for cwdxHeSuStatusValue."
- REFERENCE
- "cwdxHeSuStatusValue object."
- ::= { cwdxHeSuStatusExtEntry 8 }
-
- cwdxIfHeSuStatusMaxOfflineTime OBJECT-TYPE
- SYNTAX TimeInterval
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The maximum period of time the SU stayed 'offline' over
- the time period from the SU's first ranging message
- received by HE until now.
-
- The SU is considered as 'online' when the value for
- cwdxHeSuStatusValue is any of the values: online(5),
- onlineNetAccessDisabled(6), onlineKekAssigned(7), and
- onlineTekAssigned(8), and the SU is considered as
- 'offline' for other values for cwdxHeSuStatusValue."
- REFERENCE
- "cwdxHeSuStatusValue object."
- ::= { cwdxHeSuStatusExtEntry 9 }
-
- cwdxIfHeSuStatusDynSidCount OBJECT-TYPE
- SYNTAX INTEGER(0..16383)
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The number of active dynamic sids on this SU."
- ::= { cwdxHeSuStatusExtEntry 10 }
- --
- -- HE MAC extension Table
- --
- -- This table extends the attributes for HE MAC interface.
- --
- -- This table includes attributes of the Subscriber-unit notification
- -- enabling/disabling and the interval of Subscriber-unit notification sent
- -- by the HE for a Subscriber-unit that the Mac interface supports.
- --
-
- cwdxHeMacExtTable OBJECT-TYPE
- SYNTAX SEQUENCE OF CwdxHeMacExtEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "This table contains the additions attributes of a HE MAC
- interface that provided by cwdIfHeMacTable."
- ::= { cwdxHeSuCpeObjects 4 }
-
- cwdxHeMacExtEntry OBJECT-TYPE
- SYNTAX CwdxHeMacExtEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "Additional objects for cwdIfHeMacTable entry including
- the Subscriber-unit notification enable/disable and the
- interval of Subscriber-unit notification sent by the HE
- for a Subscriber-unit that the Mac interface supports.
- An entry in this table exists for each ifEntry with an
- ifType of propDocsWirelessMacLayer(nnn)."
- REFERENCE
- "cwdIfHeMacTable in CISCO-WIRELESS-DOCS-IF-MIB.my."
- AUGMENTS { cwdIfHeMacEntry }
- ::= { cwdxHeMacExtTable 1 }
-
- CwdxHeMacExtEntry ::= SEQUENCE {
- cwdxHeSuOnOffTrapEnable TruthValue,
- cwdxHeSuOnOffTrapInterval Integer32,
- cwdxHeSuDefaultMaxCpes Integer32,
- cwdxHeTotalSusRegistered Integer32,
- cwdxHeTotalSusOffline Integer32
-
- }
-
- cwdxHeSuOnOffTrapEnable OBJECT-TYPE
- SYNTAX TruthValue
- MAX-ACCESS read-write
- STATUS current
- DESCRIPTION
- "An indication of whether the cwdxHeSuOnOffNotification
- is enabled. The default value is false(2)."
- ::= { cwdxHeMacExtEntry 1 }
-
- cwdxHeSuOnOffTrapInterval OBJECT-TYPE
- SYNTAX Integer32 (0..86400)
- UNITS "seconds"
- MAX-ACCESS read-write
- STATUS current
- DESCRIPTION
- "The interval for cwdxHeSuOnOffNotification sent by HE for
- one online/offline state change if cwdxHeSuOnOffTrapEnable
- is true.
-
- If there are more than one state changes to online/offline
- for a Subscriber-unit during this interval, only one
- cwdxHeSuOnOffNotification is sent by HE for the first
- state change to online and one cwdxHeSuOnOffNotification
- for the first state changing to offline if
- cwdxHeSuOnOffTrapEnable is true.
-
- This is to avoid too many notifications sent for a
- SU online/offline state changes during a short period
- of time.
-
- If the value is 0, then cwdxHeSuOnOffNotification will be
- sent for every state change to online/offline for a
- SU if cwdxHeSuOnOffTrapEnable is true.
-
- This object's value will be retained even if the
- cwdxHeSuOnOffTrapEnable value changes. Thus disabling
- notifications will not result in this object's value
- being reset tot he default value.
-
- The default value is 600 seconds."
- ::= { cwdxHeMacExtEntry 2 }
-
- cwdxHeSuDefaultMaxCpes OBJECT-TYPE
- SYNTAX Integer32 (0..255)
- MAX-ACCESS read-write
- STATUS current
- DESCRIPTION
- "The default maximum number of permitted CPEs per SU
- in this wireless interface. A SU can override this
- value by setting the object cwdxHeSuMaxCpeNumber
- in the cwdxHeSuTable.
-
- The value 0 means no maximum limit.
-
- The default value for this object is 0.
-
- Setting the value will not affect the already connected
- CPEs to the SUs in this wireless interface."
- ::= { cwdxHeMacExtEntry 3 }
-
- cwdxHeTotalSusRegistered OBJECT-TYPE
- SYNTAX Integer32 (0..2147483647)
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "Total number of SUs that successfully registered at
- least once with this HE. This count will be decremented
- whenever the SUs are aged out at the HE."
- ::= { cwdxHeMacExtEntry 4 }
-
- cwdxHeTotalSusOffline OBJECT-TYPE
- SYNTAX Integer32 (0..2147483647)
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "Total number of SU's that are offline at this time.
- The SU is considered as 'online' when the value for
- cwdxHeSuStatusValue is any of the values: online(5),
- onlineNetAccessDisabled(6), onlineKekAssigned(7), and
- onlineTekAssigned(8), and the SU is considered as
- 'offline' for other values for cwdxHeSuStatusValue."
- ::= { cwdxHeMacExtEntry 5 }
-
-
- --
- -- HE SU channel override operation table and the related
- -- objects
- --
- -- An HE operator may perform downstream/upstream load balancing
- -- or failure recovery using cwdxHeSuChOverTable. An entry
- -- in this table is an operation from HE to generate downstream
- -- frequency and upstream channel override fields in the RNG-RSP message
- -- sent to a Subscriber-unit. A RNG-RSP message is sent to a Subscriber-unit
- -- during initial maintenance opportunity.
- --
- -- This operation causes the HE to place an entry for the
- -- SU specified into the override request queue. The link is
- -- then broken by deleting the SU from its polling list. When
- -- the SU attempts initial ranging, the override request
- -- causes downstream frequency and upstream channel override
- -- fields to be inserted into the RNG-RSP message.
- --
-
- cwdxHeSuChOverTimeExpiration OBJECT-TYPE
- SYNTAX Integer32 (1..86400)
- UNITS "minutes"
- MAX-ACCESS read-write
- STATUS current
- DESCRIPTION
- "The time period to expire a HE channel override operation.
- Within the time period, if the HE cannot send out a
- RNG-RSP message with channel override fields to a
- SU specified in the operation, the HE will abort
- the operation. The possible reason is that the
- SU does not repeat the initial ranging.
-
- The change to this object will not affect the already active
- operations in this cwdxHeSuChOverTable.
-
- Once the operation completes, the management station should
- retrieve the values of the cwdxHeSuChOverState
- object of interest, and should then delete the entry
- from cwdxHeSuChOverTable. In order to prevent old
- entries from clogging the table, entries will be aged out,
- but an entry will never be deleted within 15 minutes of
- completing."
- REFERENCE
- "Data-Over-Cable Service Interface Specifications (DOCSIS)
- Radio Frequency Interface Specification (SP-RFI-I04-980724),
- 6.3.2.5.3 Overriding Channels."
- ::= { cwdxHeSuCpeObjects 5 }
-
-
- cwdxHeSuChOverTable OBJECT-TYPE
- SYNTAX SEQUENCE OF CwdxHeSuChOverEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "A table of HE operation entries to instruct Subscriber-units
- to move to a new downstream and/or upstream channel.
-
- An entry in this table is an operation that has been
- initiated from HE to generates downstream frequency and/or
- upstream channel override fields in the RNG-RSP message sent
- to a Subscriber-unit. A RNG-RSP message is sent to a
- SU during initial maintenance opportunity.
-
- This operation causes the HE to place an entry for the
- SU specified into the override request queue. The link is
- then broken by deleting the SU from its polling list. When
- the SU attempts initial ranging, the override request
- causes downstream frequency and upstream channel override
- fields to be inserted into the RNG-RSP message."
- ::= { cwdxHeSuCpeObjects 6 }
-
- cwdxHeSuChOverEntry OBJECT-TYPE
- SYNTAX CwdxHeSuChOverEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "An HE operation entry to instruct a Subscriber-unit to move
- to a new downstream and/or upstream channel.
-
- There can be more than one entry per Subscriber-unit,
- so there is a time stamp for each entry to show the time
- when this operation is initiated.
-
- A management station wishing to create an entry should
- first generate a pseudo-random serial number to be used
- as the index to this sparse table. The station should
- then create the associated instance of the row status
- object. It must also, either in the same or in successive
- PDUs, create the associated instance of the command and
- parameter objects. It should also modify the default values
- for any of the parameter objects if the defaults are not
- appropriate.
-
- Once the appropriate instances of all the command
- objects have been created, either by an explicit SNMP
- set request or by default, the row status should be set
- to active to initiate the operation. Note that this entire
- procedure may be initiated via a single set request which
- specifies a row status of createAndGo as well as specifies
- valid values for the non-defaulted parameter objects.
-
- Once an operation has been activated, it cannot be stopped.
- That is, it will run until either the HE has generated
- downstream frequency and/or upstream channel override fields
- in the RNG-RSP message sent to a Subscriber-unit or time out.
- In either case, the operation is completed. During this
- time the row cannot be destroyed.
-
- Once the operation is completed, the real result of the
- operation to the Subscriber-unit cannot be known from this table.
- The result of the Subscriber-unit's downstream frequency and the
- upstream channel id can be checked from other MIB tables.
- For example, cwdIfHeServiceTable from
- CISCO-WIRELESS-DOCS-IF-MIB can be used to check
- whether the Subscriber-unit's downstream frequency
- and upstream channel id are changed. Please note that even
- though HE has generated downstream frequency and/or
- upstream channel override fields in the RNG-RSP message sent
- to a SUs if the SU cannot lock at the instructed downstream
- frequency or no upstream channel id could be used, it may
- reconnect back to the original downstream frequency and
- upstream channel id.
-
- Once the operation completes, the management station should
- retrieve the values of the cwdxHeSuChOverState
- objects of interest, and should then delete the entry.
- In order to prevent old entries from clogging the table,
- entries will be aged out, but an entry will never be deleted
- within 15 minutes of completing."
- REFERENCE
- "Data-Over-Cable Service Interface Specifications (DOCSIS)
- Radio Frequency Interface Specification (SP-RFI-I04-980724),
- 6.3.2.5.3 Overriding Channels."
- INDEX { cwdxHeSuChOverSerialNumber }
- ::= { cwdxHeSuChOverTable 1 }
-
- CwdxHeSuChOverEntry ::= SEQUENCE {
- -- index
- cwdxHeSuChOverSerialNumber Integer32,
- -- operation items
- cwdxHeSuChOverMacAddress MacAddress,
- cwdxHeSuChOverDownFrequency Integer32,
- cwdxHeSuChOverUpChannelId Integer32,
- cwdxHeSuChOverTrapOnCompletion TruthValue,
- -- status items
- cwdxHeSuChOverOpInitiatedTime TimeStamp,
- cwdxHeSuChOverState INTEGER,
- cwdxHeSuChOverRowStatus RowStatus
- }
-
- cwdxHeSuChOverSerialNumber OBJECT-TYPE
- SYNTAX Integer32 (1..2147483647)
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "Object which specifies a unique entry in the
- table. A management station wishing to initiate a
- channel override operation should use a pseudo-random
- value for this object when creating or modifying an
- instance of a cwdxHeSuChOverEntry."
- ::= { cwdxHeSuChOverEntry 1 }
-
- cwdxHeSuChOverMacAddress OBJECT-TYPE
- SYNTAX MacAddress
- MAX-ACCESS read-create
- STATUS current
- DESCRIPTION
- "The mac address of the Subscriber-unit that the HE instructs to
- move to a new downstream and/or upstream channel.
-
- This column must be set to a valid Mac address currently in
- the HE in order for this entry's row status to be set to
- active successfully."
- ::= { cwdxHeSuChOverEntry 2 }
-
- cwdxHeSuChOverDownFrequency OBJECT-TYPE
- SYNTAX Integer32 (0..1000000000)
- UNITS "hertz"
- MAX-ACCESS read-create
- STATUS current
- DESCRIPTION
- "The new downstream frequency which the Subscriber-unit is
- instructed to move to. The value 0 is to ask the HE not to
- override the downstream frequency."
- DEFVAL { 0 }
- ::= { cwdxHeSuChOverEntry 3 }
-
- cwdxHeSuChOverUpChannelId OBJECT-TYPE
- SYNTAX Integer32 (-1..255)
- MAX-ACCESS read-create
- STATUS current
- DESCRIPTION
- "The new channel Id which the Subscriber-unit is instructed to
- move to. The value -1 is to ask the HE not to override
- the upstream channel Id."
- DEFVAL { -1 }
- ::= { cwdxHeSuChOverEntry 4 }
-
- cwdxHeSuChOverTrapOnCompletion OBJECT-TYPE
- SYNTAX TruthValue
- MAX-ACCESS read-create
- STATUS current
- DESCRIPTION
- "Specifies whether or not a cwdxHeSuChOverNotification
- should be issued on completion of the operation. If such a
- notification is desired, it is the responsibility of the
- management entity to ensure that the SNMP administrative model
- is configured in such a way as to allow the notification to be
- delivered."
- DEFVAL { false }
- ::= { cwdxHeSuChOverEntry 5 }
-
- cwdxHeSuChOverOpInitiatedTime OBJECT-TYPE
- SYNTAX TimeStamp
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The value of sysUpTime at which the operation was initiated.
- Since it is possible to have more than one entry in this
- table for a Subscriber-unit, this object can help to distinguish
- the entries for the same Subscriber-unit."
- ::= { cwdxHeSuChOverEntry 6 }
-
- cwdxHeSuChOverState OBJECT-TYPE
- SYNTAX INTEGER {
- messageSent(1),
- commandNotActive(2),
- noOpNeeded(3),
- suNotFound(4),
- waitToSendMessage(5),
- timeOut(6)
- }
- MAX-ACCESS read-only
- STATUS current
- DESCRIPTION
- "The status of the specified channel override operation.
- The enumerations are:
- messageSent(1): the HE has sent a RNG-RSP message
- with channel override to the Subscriber-unit.
- commandNotActive(2): the command is not in active mode
- due to this entry's row status is not
- in active yet.
- noOpNeeded(3): The downstream frequency and the upstream
- channel Id in this entry are the same as
- original ones when this entry's row status
- is set to active, so HE does not need to
- do any operation.
- SuNotFound(4): The SU is not found in the HE
- at the time when the command becomes
- active.
- waitToSendMessage(5): specified the operation is active
- and HE is waiting to send
- a RNG-RSP message with channel
- override to the Subscriber-unit.
- timeOut(6): specified the operation is timed out.
- That is, the HE cannot send a RNG-RSP message
- with channel override to the Subscriber-unit within
- the time specified in the object of
- cwdxHeSuChOverTimeExpiration.
- The possible reason is that the Subscriber-unit
- does not repeat the initial ranging.
-
- The possible state change diagram is as below:
- [commandNotActive ->] waitToSendMessage ->
- messageSent or timeOut.
- [commandNotActive ->] noOpNeeded or SuNotFound."
- REFERENCE
- "Data-Over-Cable Service Interface Specifications (DOCSIS)
- Radio Frequency Interface Specification (SP-RFI-I04-980724),
- 6.3.2.5.3 Overriding Channels."
- ::= { cwdxHeSuChOverEntry 7 }
-
- cwdxHeSuChOverRowStatus OBJECT-TYPE
- SYNTAX RowStatus
- MAX-ACCESS read-create
- STATUS current
- DESCRIPTION
- "The status of this table entry.
-
- This value for cwdxHeSuChOverMacAddress must be valid Mac
- address currently in the HE in order for the row
- status to be set to active successfully.
-
- Once the row status becomes active and state becomes
- waitToSendMessage, the entry cannot not be changed except
- to delete the entry by setting the row status to destroy(6)
- and since the operation cannot be stopped, the destroy(6)
- will just cause the SNMP agent to hide the entry from
- application and the SNMP agent will delete the entry
- right after the operation is completed."
- ::= { cwdxHeSuChOverEntry 8 }
-
- --
- -- HE Subscriber-unit (SU) Table
- --
- -- This table contains attributes or configurable parameters
- -- for Subscriber-units from a HE.
- --
- -- An HE operator can use this table to report a Subscriber-unit's
- -- attributes or configure a Subscriber-unit by a Subscriber-unit's
- -- MAC address.
- --
-
- cwdxHeSuTable OBJECT-TYPE
- SYNTAX SEQUENCE OF CwdxHeSuEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "This table contains attributes or configurable parameters
- for Subscriber-units from a HE."
- ::= { cwdxHeSuCpeObjects 7 }
-
- cwdxHeSuEntry OBJECT-TYPE
- SYNTAX CwdxHeSuEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "The list contains a SU's attributes or
- configurable parameters from a HE."
- INDEX { cwdIfHeSuStatusIndex }
- ::= { cwdxHeSuTable 1 }
-
- CwdxHeSuEntry ::= SEQUENCE {
- cwdxHeSuMaxCpeNumber Integer32
- }
-
- cwdxHeSuMaxCpeNumber OBJECT-TYPE
- SYNTAX Integer32 (-1..255)
- MAX-ACCESS read-write
- STATUS current
- DESCRIPTION
- "The maximum number of permitted CPEs connecting to the
- SU.
-
- The value -1 means to use the default value of maximum
- hosts per SU in the HE wireless interface which the SU
- connects to and the value is defined in
- cwdxHeSuDefaultMaxCpes in the cwdxHeMacExtTable.
-
- The value 0 means no maximum limit.
-
- The default value is -1.
-
- Setting the value will not affect the already connected
- CPEs to the SU."
- ::= { cwdxHeSuEntry 1 }
-
- --
- -- Quality of Service Extension table
- --
-
- cwdxQosProfileExtTable OBJECT-TYPE
- SYNTAX SEQUENCE OF CwdxQosProfileExtEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "This table contains additional attributes to the Qos
- profiles that exists in cwdIfQosProfileTable in
- CISCO-WIRELESS-DOCS-IF-MIB."
- ::= { cwdxQosProfileExtObjects 1 }
-
- cwdxQosProfileExtEntry OBJECT-TYPE
- SYNTAX CwdxQosProfileExtEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "Each row extends the existing row in the
- cwdIfQosProfileTable with additional QOS parameters."
- AUGMENTS { cwdIfQosProfileEntry }
- ::= { cwdxQosProfileExtTable 1 }
-
- CwdxQosProfileExtEntry ::= SEQUENCE {
- cwdxQosProfGrantInterval INTEGER,
- cwdxQosProfGrantSize INTEGER,
- cwdxQosProfName DisplayString,
- cwdxQosProfTosOverwriteMask INTEGER,
- cwdxQosProfTosOverwriteValue INTEGER
- }
-
- cwdxQosProfGrantInterval OBJECT-TYPE
- SYNTAX INTEGER (0..65535)
- UNITS "milliseconds"
- MAX-ACCESS read-create
- STATUS current
- DESCRIPTION
- "The value of this parameter specifies the interval
- between successive data grant opportunities for a
- service flow. This object is required for
- Unsolicited Grant and Unsolicited Grant with
- Activity Detection Service Flows. This object is
- optional for Real-Time Polling Service Flows."
- REFERENCE
- "Data over Cable Radio Frequency Interface Specification,
- SP-RFIv1.1-I02-990731 Appendix M.1.2"
- DEFVAL{ 20 }
- ::= { cwdxQosProfileExtEntry 1 }
-
- cwdxQosProfGrantSize OBJECT-TYPE
- SYNTAX INTEGER (0..65535)
- UNITS "bytes"
- MAX-ACCESS read-create
- STATUS current
- DESCRIPTION
- "This parameter specifies the unsolicited grant size."
- REFERENCE
- "Data over Cable Radio Frequency Interface Specification,
- SP-RFIv1.1-I02-990731 Appendix M.1.2"
- DEFVAL{ 229 }
- ::= { cwdxQosProfileExtEntry 2 }
-
- cwdxQosProfName OBJECT-TYPE
- SYNTAX DisplayString(SIZE(0..64))
- MAX-ACCESS read-create
- STATUS current
- DESCRIPTION
- "This object is a string used to describe this Qos
- Profile. It has informational significance only."
- DEFVAL{ "" }
- ::= { cwdxQosProfileExtEntry 3 }
-
- cwdxQosProfTosOverwriteMask OBJECT-TYPE
- SYNTAX INTEGER (0..255)
- MAX-ACCESS read-create
- STATUS current
- DESCRIPTION
- "This object is the bit mask (8 bit wide) for
- tos-overwrite feature. The
- cwdxQosProfTosOverwriteValue is written where the
- mark bits are set to 1.
- Tos-overwrite allows the HE to mark egress IP packets
- (from the HE) with a specific TOS value. This relieves
- the subscriber unit from marking upstream packets with
- a specific TOS and is most useful when a subscriber
- unit is supplied by a third party vendor who may not
- have the option of applying a TOS to an IP packet.
- Each packet received from an SU that matches this QoS
- profile will be tagged with the TOS-overwrite value
- at the cwdxQosProfTosOverwriteMask and sent to the
- network."
- DEFVAL { 0 }
- ::= { cwdxQosProfileExtEntry 4 }
-
- cwdxQosProfTosOverwriteValue OBJECT-TYPE
- SYNTAX INTEGER (0..255)
- MAX-ACCESS read-create
- STATUS current
- DESCRIPTION
- "This object is the byte value for tos-overwrite. The
- cwdxQosProfTosOverwriteValue is written where the mark
- bits are set to 1.
- Each packet received from an SU that matches this QoS
- profile will be tagged with the
- cwdxQosProfTosOverwriteValue value at the
- cwdxQosProfTosOverwriteMask and sent to the
- network."
- DEFVAL { 0 }
- ::= { cwdxQosProfileExtEntry 5 }
-
-
- cwdxQosIpTosRatelimitTable OBJECT-TYPE
- SYNTAX SEQUENCE OF CwdxQosIpTosRatelimitEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "Describes the Ip-precedence attached to every
- Qos Profile identified by a row in
- cwdIfQosProfileTable in CISCO-WIRELESS-DOCS-IF-MIB."
- ::= { cwdxQosProfileExtObjects 2 }
-
- cwdxQosIpTosRatelimitEntry OBJECT-TYPE
- SYNTAX CwdxQosIpTosRatelimitEntry
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "Describes the Ip Precedence parameters. For every
- QOS profile entry in the cwdIfQosProfileTable,
- there will be seven corresponding rows in this
- cwdxQosIpTosRatelimitTable.
-
- The default value of 0 will be assigned to
- cwdxQosIpTosRatelimitMaxDownRate for all the
- rows."
- INDEX {cwdIfQosProfIndex, cwdxQosIpTosRatelimitIndex }
- ::= { cwdxQosIpTosRatelimitTable 1 }
-
- CwdxQosIpTosRatelimitEntry ::= SEQUENCE {
- cwdxQosIpTosRatelimitIndex INTEGER,
- cwdxQosIpTosRatelimitMaxDownRate INTEGER
- }
-
- cwdxQosIpTosRatelimitIndex OBJECT-TYPE
- SYNTAX INTEGER (1..8)
- MAX-ACCESS not-accessible
- STATUS current
- DESCRIPTION
- "The index value along with the primary index of
- cwdIfQosProfIndex which uniquely identifies an entry
- in the cwdxQosIpTosRatelimitEntry."
- ::= { cwdxQosIpTosRatelimitEntry 1 }
-
- cwdxQosIpTosRatelimitMaxDownRate OBJECT-TYPE
- SYNTAX INTEGER (0..100000000)
- UNITS "bps"
- MAX-ACCESS read-write
- STATUS current
- DESCRIPTION
- "Maximum downstream rate that can be allowed with
- this IP precedence."
- ::= { cwdxQosIpTosRatelimitEntry 2 }
-
- --
- -- The Cisco DOCS Extension MIB Notifications
- --
-
- ciscoWirelessDocsExtNotificationsPrefix OBJECT IDENTIFIER
- ::= { ciscoWirelessDocsExtMIB 2 }
- ciscoWirelessDocsExtNotifications OBJECT IDENTIFIER
- ::= { ciscoWirelessDocsExtNotificationsPrefix 0 }
-
-
- cwdxHeSuOnOffNotification NOTIFICATION-TYPE
- OBJECTS { cwdIfHeSuStatusMacAddress,
- cwdIfHeSuStatusIpAddress,
- cwdIfHeSuStatusDownChanIfIndex,
- cwdIfHeSuStatusUpChanIfIndex,
- cwdIfHeSuStatusServiceId,
- cwdxHeSuStatusValue
- }
- STATUS current
- DESCRIPTION
- "This notification indicates that the SU coming online
- and going offline. A notification will be sent from HE for
- a SU status changing to online or offline
- within the interval specified in cwdxHeSuOnOffTrapInterval."
- ::= { ciscoWirelessDocsExtNotifications 1 }
-
-
- cwdxHeSuChOverNotification NOTIFICATION-TYPE
- OBJECTS { cwdxHeSuChOverMacAddress,
- cwdxHeSuChOverDownFrequency,
- cwdxHeSuChOverUpChannelId,
- cwdxHeSuChOverOpInitiatedTime,
- cwdxHeSuChOverState
- }
- STATUS current
- DESCRIPTION
- "This notification is sent at the completion of a HE
- channel override operation if
- cwdxHeSuChOverTrapOnCompletion is true in the
- original entry.
-
- Once a channel override operation has been activated, it
- cannot be stopped. That is, it will run until either the
- HE has generated downstream frequency and/or upstream
- channel override fields in the RNG-RSP message sent to a
- HE or cwdxHeSuChOverTimeExpiration time expired.
- In either case, the operation is completed. State in the
- cwdxHeSuChOverState object will tell in which
- condition the operation is completed."
- ::= { ciscoWirelessDocsExtNotifications 2 }
-
-
-
-
- --
- -- The Cisco DOCS Extension MIB Conformance Statements
- --
-
- --
- -- Conformance statement
- --
-
- ciscoWirelessDocsExtConformance OBJECT IDENTIFIER
- ::= { ciscoWirelessDocsExtMIB 3 }
- cwdxDocsExtCompliances OBJECT IDENTIFIER
- ::= { ciscoWirelessDocsExtConformance 1 }
- cwdxDocsExtGroups OBJECT IDENTIFIER
- ::= { ciscoWirelessDocsExtConformance 2 }
-
-
- -- compliance statements
-
- cwdxDocsExtCompliance MODULE-COMPLIANCE
- STATUS current
- DESCRIPTION
- "The compliance statement for devices that implement MCNS
- compliant Radio Frequency Interfaces and DOCSIS features."
- MODULE -- this module
- MANDATORY-GROUPS {
- cwdxQosCtrlGroup,
- cwdxQosQueueGroup,
- cwdxHeSuCpeGroup
- }
-
- OBJECT cwdxHeSuChOverTimeExpiration
- MIN-ACCESS read-only
- DESCRIPTION
- "Write access is not required."
- ::= { cwdxDocsExtCompliances 1 }
-
-
- -- MIB groupings
-
- cwdxQosCtrlGroup OBJECT-GROUP
- OBJECTS {
- cwdxQosCtrlUpAdmissionCtrl,
- cwdxQosCtrlUpMaxRsvdBWPercent,
- cwdxQosCtrlUpAdmissionRejects,
- cwdxQosCtrlUpReservedBW,
- cwdxQosCtrlUpMaxVirtualBW,
- cwdxQosIfRateLimitAlgo,
- cwdxQosIfRateLimitExpWgt,
- cwdxQosIfRateLimitShpMaxDelay,
- cwdxQosIfRateLimitShpGranularity,
- cwdxIfHeServiceOutOctets,
- cwdxIfHeServiceOutPackets,
- cwdxQosMaxUpBWExcessRequests,
- cwdxQosMaxDownBWExcessPackets,
- cwdxQosProfGrantInterval,
- cwdxQosProfGrantSize,
- cwdxQosProfName,
- cwdxQosProfTosOverwriteMask,
- cwdxQosProfTosOverwriteValue,
- cwdxQosIpTosRatelimitMaxDownRate
- }
- STATUS current
- DESCRIPTION
- "Group of objects implemented in HE wireless
- interfaces for states of the scheduler supporting
- Data-Over-Cable Service Interface Specifications (DOCSIS)
- 1.0 Quality of Service (QoS)."
- ::= { cwdxDocsExtGroups 1 }
-
- cwdxQosQueueGroup OBJECT-GROUP
- OBJECTS {
- cwdxBWQueueOrder,
- cwdxBWQueueNumServedBeforeYield,
- cwdxBWQueueType,
- cwdxBWQueueMaxDepth,
- cwdxBWQueueDepth,
- cwdxBWQueueDiscards
- }
- STATUS current
- DESCRIPTION
- "Group of objects implemented in HE wireless interfaces
- for the queuing states of the scheduler supporting
- Data-Over-Cable Service Interface Specifications
- (DOCSIS) 1.0 Quality of Service (QoS). Each upstream scheduler
- maintains a queue set, but the downstream schedulers does not
- in DOCSIS 1.0 QoS. So only each upstream has an entry for
- DOCSIS 1.0 QoS support."
- ::= { cwdxDocsExtGroups 2 }
-
- cwdxHeSuCpeGroup OBJECT-GROUP
- OBJECTS {
- cwdxCpeIpAddress,
- cwdxCpeAccessGroup,
- cwdxSuMappingStatusIndex,
- cwdxHeSuStatusValue,
- cwdxIfHeSuStatusOnlineTimes,
- cwdxIfHeSuStatusPercentOnline,
- cwdxIfHeSuStatusMinOnlineTime,
- cwdxIfHeSuStatusAvgOnlineTime,
- cwdxIfHeSuStatusMaxOnlineTime,
- cwdxIfHeSuStatusMinOfflineTime,
- cwdxIfHeSuStatusAvgOfflineTime,
- cwdxIfHeSuStatusMaxOfflineTime,
- cwdxIfHeSuStatusDynSidCount,
- cwdxHeSuOnOffTrapEnable,
- cwdxHeSuOnOffTrapInterval,
- cwdxHeSuDefaultMaxCpes,
- cwdxHeTotalSusRegistered,
- cwdxHeTotalSusOffline,
- cwdxHeSuChOverTimeExpiration,
- cwdxHeSuChOverMacAddress,
- cwdxHeSuChOverDownFrequency,
- cwdxHeSuChOverUpChannelId,
- cwdxHeSuChOverTrapOnCompletion,
- cwdxHeSuChOverOpInitiatedTime,
- cwdxHeSuChOverState,
- cwdxHeSuChOverRowStatus,
- cwdxHeSuMaxCpeNumber
- }
- STATUS current
- DESCRIPTION
- "Group of objects implemented in HE for managing and
- monitoring Customer Premises Equipments."
- ::= { cwdxDocsExtGroups 3 }
-
-
- END
-